How Often To Change 7.3 Fuel Filter
Ford advises 6.vii Powerstroke owners to change their fuel filters after every 15,000 miles of travel, during the tertiary oil change, or equally suggested by the message on the musical instrument cluster. Owners can human activity on these depending on which one comes first. Other online sources suggest irresolute information technology later on every 20,000 – twoscore,000 miles of travel.
Changing your fuel filter on six.seven Powerstroke helps to remove impurities, debris, and particles that may preclude your engine from performing at its height. It may forcefulness the engine pump to work harder if it's clogged. This and so leads to breakdown and damage to the engine due to contaminated fuel. A damaged engine is characterized by bad gas, sluggish acceleration[note]https://dynref.engr.illinois.edu/ava.html[/note], difficulty in starting, decreased fuel economy, and frequent stalls.
Ford likewise advises 6.vii Powerstroke owners to go for those built by Motorcraft[annotation]https://en.wikipedia.org/wiki/Motorcraft[/note]. These are specifically designed to meet the demands and needs of the Powerstroke engine. They are of the correct size and quality and provide amend filtration without requiring an adaptor. Still, a fuel filter from any other reputable make should too practise the trick. Below is a step-by-step process that will show yous how to change yours on the half dozen.vii Powerstroke.
What you volition need to follow this tutorial
- Gloves
- 32 mm socket wrench
- New OEM fuel filter
[pt_view id="a305351pkh"]
Step by step instructions
The Ford 6.7 Powerstroke is equipped with two sealed cartridge fuel filters. The main ane is found at the lesser of the motorcar, about in the middle of the chassis along the driver's frame runway. The second is plant on top of the engine.
Main Filter
one. Locate the main filter
As mentioned, the main filter is located at the bottom of the truck. You can find it forth the driver's frame rail. Y'all may experience some obstruction from wire harnesses and brake lines depending on the model year.
two. Drain all the fluid
Once you locate the master filter forth the driver frame rail, start by disconnecting the fluid sensor to forestall it from getting damaged by water and fuel. Place an empty jar below the valve and open information technology to drain the fluid. You can proceed with the adjacent step as the fluid flows out.
three. Remove the plastic housing
Use the 32 mm socket wrench to remove the filter housing. It will accept an average of five to 6 turns for it to completely come off. The housing may come off together with the old filter. If it doesn't, pull it out.
4. Clean the housing
Your filter housing may have mud, debris, or sand in it. Wipe everything off with a clean cloth. Retrieve besides to make clean the grooves which the housing screws into.
5. Replace the old O-band
Every new fuel filter comes with a new O-ring. Replace the old with the new. Make sure it fits perfectly on the peak-most groove.
half dozen. Install the new fuel filter
Insert the new fuel filter together with the clean housing. Plow the whole unit by manus until you lot feel it tighten. Avoid screwing it in place using a wrench every bit you might break it. Remember to reconnect the fuel and water sensor after completing your installation.
Secondary Fuel Filter
ane. Disconnect the fuel lines
In one case you locate the secondary fuel filter on top of the engine, you'll need to disconnect the two fuel lines establish above information technology. The first line requires you lot to squeeze the two tabs at the bottom of the colored clamp and pull it upwards. You can identify a rag under the clamp to catch the drops of fuel draining from the line. The 2d line requires you to clasp 2 tabs institute on either side of the clamp before pulling the line out.
two. Remove the old filter
Once the fuel lines are disconnected, turn the plastic housing counterclockwise to remove information technology.
3. Install the new filter
Supersede the erstwhile filter with the new one. Both volition be contained within their corresponding housings, and yous will not need to open up them upward. Once washed, lock the new filter in place and push button your fuel lines back on.
iv. Wheel the key 6 times
The side by side step is to identify the key into the ignition. Switch on the truck half-dozen times at 30-second intervals. This helps to rid the engine of any unwanted air. Skipping this step increases the chance of getting air in the loftier-force per unit area fuel parts.
5. Check your settings
For models not older than 2011, you'll demand to ringlet through your settings to confirm the new modify. Scroll downwards to Settings > Vehicle > Maintenance > Fuel Filter > Hold OK if Fuel Filter Changed . You should see a notification that says "Fuel Filter Ready to New."
Conclusion
Particulates from several sources can penetrate into the gas tank through breathers and vents. Such contaminants and other abrasive particles can chop-chop impairment an engine. The fuel filter's about important role is to rid the engine of these particles. Its other role includes acting as a water separator.
When water mixes with diesel fuel, it causes a reduction in ability and the quality of fuel burn. It also makes engine components such as pumps and injectors to corrode. Vesture and tear of fuel injectors are ane of the major causes of early injector replacements.
This makes it extremely important to change your fuel filter after every 15,000 – 25,000 miles. This post provides a detailed process of irresolute both the main and secondary filters in a six.seven Powerstroke[notation]http://ophelia.sdsu.edu:8080/ford/09-29-2013/news-center/press-releases-detail/2015-ford-f-series-super-duty-features-improved-ability-stroke-die.html[/notation]. Let me know in the comment department if this was helpful. Do share if you liked it!
Source: https://carwrenching.com/how-often-to-change-the-fuel-filter-on-a-6-7-powerstroke/
Posted by: milnelatim1936.blogspot.com
0 Response to "How Often To Change 7.3 Fuel Filter"
Post a Comment